Ademco XM/First Alert FAC Program Sheet. Enter Program 1. + 8 + 0 + 0 (Display should show 00). or. 2. Power down then back up and press. The Ademco XM is a UL Listed commercial fire and burglary control system. Its advanced integrated design is aimed at providing a powerful solution for the. ADDENDUM TO: INSTALLATION INSTRUCTIONS FOR XM CONTROL Ademco High Speed off-normal test reports use channel 3 =1 and status channel .
|Published (Last):||1 November 2018|
|PDF File Size:||4.87 Mb|
|ePub File Size:||15.27 Mb|
|Price:||Free* [*Free Regsitration Required]|
Seller’s payment instructions Free shipping is for the lower 48 US states only. For any other zone types, proceed to the next step. Determine the maximum device loading on the polling loop branch by adding the load currents per device determined from Table 2.
Ground Fault Voltages – 13 – Updated: With this field enabled, no other polling loop devices will operate. See all condition definitions – opens in a new window or tab Isolate this by checking voltage on the polling loop with wires connected and with all wires removed. This will not affect panels that do not support the feature, but if the panel does support this adfmco then it must be enabled per 51400xm zone.
The zone should go into check. Ask your installer if your system was set up to allow system zones and conditions for problems such as zone wire breaks, loss of AC power, faulted telephone system outputs to be bypassed. Comments to this Manuals Your Name. Be the first to write a review.
This verifies that the panel is able to talk to the device as well as the proper serial number. This is only a display difference. This cannot be disabled by a dip-switch like the sd. Immediate payment required for this item.
Ademco VISTA 5140XM User Manual
Estimated on or before Wed. Please note ship times are calculated based on physical addresses in the lower 48 US states. Verify that all devices are correctly wired. Edmonton, London, United Kingdom. Sign in to check out Check out as guest.
Remove polling loop from panel and verify the voltage returns. Any of these may be used. Seller’s obligation is limited to repairing. For specific notes on V-plex smoke detectors and motion sensors, see notes under the appropriate sections.
Verify the zones are correctly wired and on the correct terminals. Some peripheral devices C for example Use a common negative to their chassis.
In this case, if the cabinet is grounded or has conduit that is grounded, an earth ground fault would be sensed through the other connections to the device. Mouse over to zoom – Click to enlarge.
The maximum number of modules which can be 5140xk in parallel to a single system control is limited to no more than 8, and by the maximum wire lengths specified above and the need for the Aux or Local power source to supply 50 ma per It is often easy to misinterpret our instructions and connect devices incorrectly.
Anything that affects the voltage potential between earth ground and the rest of the system would cause the system to report an earth ground fault, even though there is not, in fact, a real zdemco ground fault.
Index of /manuals/Ademco//Control Panels/5140XM
Subject to credit approval. This continuous broadcasting can cause problems on these zones as well as other polling loop zones. Leave the earth ground wire connected during this process. Mouse over to Zoom – Click to enlarge. If not, then the zone programming is not correct. Also, try setting as a burg zone type to isolate this.
Watch list is full. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to Watch list.
UPG 12V 8Ah Battery for Ademco XM Alarm – 4 Pack | eBay
A brand-new, unused, unopened and undamaged item in original retail packaging where packaging is applicable. Vista security system installation and setup guide pages. Seller information cameraexperts1 Once you have received your goods please leave positive feedback. Can conduit that is usually grounded affect ground fault?
Report item – opens in a new window or tab. Grounding the cabinet should not cause any problems. If using Dip-Switch devices, verify that you do not have any 2 zones set for the same address. Seller information ecomelectronics