ASTM D2217 PDF

Find the most up-to-date version of ASTM D at Engineering ASTM Standards D Practice for Wet Preparation of Soil Samples for prepared in accordance with Practice D 4. Apparatus. Buy ASTM D PRACTICE FOR WET PREPARATION OF SOIL SAMPLES FOR PARTICLE-SIZE ANALYSIS AND DETERMINATION OF SOIL.

Author: Gura Moogukora
Country: Central African Republic
Language: English (Spanish)
Genre: Sex
Published (Last): 4 June 2010
Pages: 37
PDF File Size: 7.49 Mb
ePub File Size: 8.27 Mb
ISBN: 221-5-50284-930-7
Downloads: 29013
Price: Free* [*Free Regsitration Required]
Uploader: Fegrel

Further it is classified as: Procedure for the Moist Specimens. Take reading after the sample has failed. The amount of the representative sample should be enough to perform the required tests.

The choice of the preparation method depends on the properties of the soil. Above water is decanted or pipetted out and dried at C and added to the material passing No.

To know the behaviour of soils and its suitability in the site, we need to tests the soils in the field and as well as in the laboratory.

Select a representative sample by the method of quartering. Atleast minimum capacity of ml. Soil composed of vegetable tissues in various stages of decomposition usually organic odour, a dark brown or black color, a spongy consistency, and a texture varying from fibrous to amorphous. This is preferred method. Note the temperature each time. Respective samples are taken to conduct the required tests. Water Content Containers Entrapped Air Removal Apparatus.

Basic Laboratory Testing of Soils | Sravan Muguda Viswanath –

Plastic Limit wp is defined as the maximum water content at which the soil can be rolled into a thread of approximately 3mm in diameter without breaking. Help Center Find new research papers in: Water Bath or a constant temperature room 8. This is done for different blows ranging between 15 to 35 blows. Then using a grooving tool the soil is taken out such that the grooving tool is always perpendicular to the cup at the time atsm. In some cases Buchner Funnels with filter paper is also used for removal of water.

  LEO BROUWER HIKA PDF

ASTM D Standard

If Method A is being followed, recommended mass of specimen should be taken for conducting the experiment. This is the atm covers the quantitative determination of the distribution of the particles. The material retained on No. ASTM D gives a guidelines for particle size analysis. Pointer will indicate maximum shear value until manually reset.

Active Risk Management

Aetm provides that the sample shall be kept at a moisture content equal or greater than the natural water content. Click here to sign up.

Passing through 75mm and retained on 19mm sieves. It is important to maintain a uniform rolling ast do not reduce the pressure as the thread diameter approaches 3mm. Particles of rock which passes through 75mm and retain on 4.

Filter Funnel or Candles 7. The torque is measured by a calibrated torque spring or torque transducer that is attached directly to the vane. Repeat until the thread shears both longitudinally and transversely when it has been rolled to about 3mm diameter, as gauged by a rod.

Soil passing through 75 m sieve that can exhibit plasticity putty like structure within a range of water contents and exhibits strength astn air dry. The TORVANE is a hand-held vane shear device for rapid determination of shear strength in cohesive soils either in the laboratory or the field. Minimum mass moist material should be representative of r2217 total sample and it depends upon the maximum particle size.

  DREMEL INTERACTIVE ANALYSIS OF WEB-SCALE DATASETS PDF

Liquid limit device 2.

The material retained on the No. This particular ASTM code explains the procedure for preparing the soils for the tests. There are two methods to find out the specific gravity of the specimen Method A: By placing the palm on top of the cylinder turn it upside down for about a min. Particles of rock which passes through 4. The pycnometer should be calibrated with respect to temperature, top meniscus of water and the water should be properly de-aired. The soil is then taken into the cup such that the surface is parallel to the horizontal.

Skip to main content. There are two ways of preparing the sample. Dry the soil sample as received from the field to the room temperature or keeping in the oven at a temperature of C. To determine the remolded shear strength of the soil, rotate the vane blade rapidly 5 to 10 times revolutions. Insert the blade of the vane into the sample atleast two times the height of the vane blade to ensure that the blade is completely embedded in the sample.

The lid used should be removed while keeping in the oven, if it is used. Flat Grooving Tool 8. Take hydrometer readings at 2,5,15,30,60 and min.