GE ASTAT PLUS PDF

GE Power Controls SOLID STATE SOFT STARTER ASTAT Plus USER MANUAL REMARKS: 1. Read this manual throughly before using the ASTAT Plus, and. General Electric/Motor Starter MPN ASTAT-QI3KDP ASTAT Plus Solid State Soft Start 50 HP Model: ASTATQI3KDP B &. Max Volts 3 Phase AC: VAC. Find great deals for GE ASTAT Plus Qi3kdp 50hp Soft Start General Electric 50 HP Starter. Shop with confidence on eBay!.

Author: Tauzshura Tokora
Country: Bulgaria
Language: English (Spanish)
Genre: History
Published (Last): 7 December 2012
Pages: 164
PDF File Size: 2.98 Mb
ePub File Size: 9.45 Mb
ISBN: 872-5-46163-664-5
Downloads: 45965
Price: Free* [*Free Regsitration Required]
Uploader: Meztigul

Secondary ramp 1 to 99 s Stopping modes All selectable Ramp dowm modes available are: Command signal may be provided by one NC free voltage push-button to terminals 2 and Select the lowest braking current and time. Please provide ALL the necessary paperwork already filled out 1 business day ahead of pickup.

Starting and stopping the motor without steps or transitions lengthens the life of power-driven machine mechanical elements, greatly reducing stress on transmission and coupling parts.

The slow speed function may be enabled by setting “Jxxx” to I3. There are 5 items available. Additional indications are given in page The above is an example given for parameter “G”, asfat all ASTAT Plus parameters zstat be modified from its default factory value proceeding in similar way.

Note that in general all reduced voltage starts produce a reduction in torque in squared proportion to the current in the phases of the motor not on the line and the latter in turn is reduced in linear proportion to the voltage. Programmable Advanced Functions Display Function Default Range Description This function provides linear acceleration and deceleration ramps in a wider range of load conditions.

  KSAWERY KNOTZ PDF

The Table A provides a complete reference as for the parameters that can be controlled by the serial interface. F to X frames 0: It’s a community-based project which helps to repair anything. Resume making your offerif the page does not update immediately. The actual value displayed can be stored in a temporal memory buffer by pressing plks.

Then the control is made thru serial comm. If the control voltage is removed after tripping, you must wait, at least, 2 minutes before the unit can be restarted. Refer to local applicable electrical codes. Sets motor current limit if parameter “N” is properly adjusted. This function needs the speed feedback provided by an external tacho generator. Motor deceleration time will depend of load conditions.

Mandatory between 2T1 and 4T2 phases, otherwise a short-circuit can occur DC brake function. Delay trip time The unit trips if the line voltage increases above of the percentage set. An isolation contactor is recommended, configured to provide automatic isolation when the motor is astzt OFF.

General Electric HP ASTAT Plus QI3NDP GE Solid State Soft Start v | eBay

Sets Voltage ramp down time. Monitor, Calibration, Basic and Advanced. An item that has been used previously. Note however that the parameter “txxx” will show the latest entry, which may differ of actual voltage value.

Reverse jog is also possible by setting “rxxx” to ON. The item you’ve selected was not added to your cart.

It is usefull to limit hammering. Values stored in the temporal memory are lost after switch off, unless these are saved in the permanent E2PROM memory through parameter “W”. Be the first to write a review. VA 17 asatt 27 38 58 75 86 67 78 88 25 32 40 63 80 2x 6, CP URC UL Ratings Current rating Max. Shipping cost cannot be calculated.

  JRC4580D DATASHEET PDF

Report item – opens in a new window or tab. Note however that the parameter “mxxx” will show the latest entry, which may differ of actual current value.

General Electric 150 HP ASTAT Plus QI3NDP GE Solid State Soft Start 150 600v

Overload relay setting should be properly coordinated with motor. See wiring diagram page This measurement must be done after complete the starting, once the motor current has been stabilized.

W – to know which overload curve is selected, the command will be: Thyristor check 1L1 3L2 or 5L3 Shortcircuit Use a testing lamp to check the defective power module between input and output phases. As a general rule it can be guaranteed that soft starter will allow starting of drives which are currently used in conventional starting systems, with the advantages outlined, and above all the facility to adjust the current peaks and torque at the machine, faced with the impossibility or difficulty of varying the steps in conventional systems.

Interest will be charged to your account from the purchase date if the balance is not paid in full within 6 months. Equipment is connected to main supply Stop Remote stop. Allows up to four tries of automatic restart after a fault. Proceed in this way untill and Keys.

If you need items quickly let us know directly to make sure we get them out for you!